What's in this guide
  1. Why is large-format tile harder to set than standard tile
  2. How flat does a slab need to be for 24x48 tile
  3. How much lippage is allowed between large tiles
  4. Why does plank tile warpage change the layout
  5. How much mortar has to be under each large tile
  6. Do tile leveling clips prevent lippage
  7. Where do movement joints and slab cracks go under large tile
  8. What should a large-format tile quote include

Large-format porcelain sets flat and flush on a Florida slab when four things are right: a slab flat to 1/8 inch in 10 feet, a large-tile mortar with full support under corners and edges, offsets of 33% or less, and soft joints over the slab’s joints. Leveling clips help set tile; they do not flatten a slab.

Why is large-format tile harder to set than standard tile?

A 12-inch tile follows the small dips in a slab without much trouble. A 24x48 plank spans them, so a hump under its middle or a dip under one end shows up as an edge sitting higher than its neighbor. The TCNA Handbook says it directly, in a passage the National Tile Contractors Association republished: “As tile size increases, the negative effect of substrate irregularities is compounded” (NTCA reprint of a TCNA article on substrate flatness).

Florida homes add three pressures. Most floors are a slab on grade, so there is nothing to shim and nothing that flexes. Open rooms with walls of sliders throw low sun across the floor, which shows every edge. And many slabs already carry shrinkage cracks, saw cuts and cold joints that the tile has to respect.

If you are still choosing between materials, our comparison of LVP and porcelain tile for Florida rooms covers that decision.

How flat does a slab need to be for 24x48 tile?

ANSI A108.02 section 4.2.2, as quoted by tile consultant Scott Carothers in How to Define Large-Format Tile and Its Subfloor Requirements (CTaSC, 2024), reads: “For tiles with at least one edge 15 in. (0.38 m) or longer, the substrate shall have a maximum permissible variation of 1/8 in. in 10 ft. (3 mm in 3 m) from the required plane, and no more than 1/16 in. variation in 24 in.,” “when measured from the high points in the surface.” Smaller tile gets a looser allowance. Our guide to checking and leveling a slab before new floors compares every floor type and covers the straightedge check, grinding and self-leveler.

The setting mortar is not a leveling tool. Custom Building Products’ data sheet for MegaLite, a large-format tile mortar (TDS-112, published December 2023), says “Thin Set Mortar should not be used to fill low spots in the flooring” and that mortar thickness should not exceed 3/4 inch when tiles are beat in. CTEF explains the risk: thin-set applied thicker than recommended “will shrink significantly,” pulling the tile with it and producing “post-installation lippage which was not present when the tile was installed” (CTEF on flatness for large format tile).

The TCNA Handbook, quoted in the same NTCA reprint, says that unless substrate prep is in the bid, “the tile contractor assumes a suitably flat substrate will be provided,” and that “Industry standards for tile finish flatness and lippage do not apply if the project owner does not provide a substrate that meets required ANSI A108.02 substrate flatness tolerances and chooses not to correct substrate flatness issues.” On a home job, the flatness check and any leveling belong in the quote as their own line.

How much lippage is allowed between large tiles?

Lippage is the height difference between the edges of neighboring tiles. The allowance depends on the grout joint and on the tile. Donato Pompo’s summary of ANSI A108.02-2023 (Tile and Stone Lippage: What is Acceptable, CTaSC, updated 2025) gives these values:

Grout joint and tileAllowable lippage (ANSI A108.02-2023 via CTaSC)
Joints 1/8 in. to less than 1/4 in. wide1/32 in., plus the inherent tile warpage
Joints 1/4 in. or wider1/16 in., plus the allowable warpage
Gauged porcelain tile, panels and slabs, any joint width1/32 in., with no additional lippage value added

The warpage term means the warpage of the tiles actually installed, not the most the tile standard would permit. The Tile Council’s lippage FAQ says “The amount of allowable tile warpage is not used in the calculation of allowable lippage” and “If there is no warpage, the lippage should not exceed the value in the table.”

The same TCNA FAQ lists what makes lippage look worse, including the “Angle of natural or manufactured light accentuating otherwise acceptable variance in modules.” In a Florida great room that means late sun skimming across the floor from a wall of sliders. A floor can meet the standard and still throw shadows at that hour, so plan the layout and joint width with that light in mind.

Why does plank tile warpage change the layout?

Long porcelain can have a slight crown or dish along its length, and ANSI A137.1 sets how much the maker may allow. CTEF notes that “with tiles becoming larger and longer, they proportionately can include more actual or inherent warpage,” and advises checking that the carton says the tile meets A137.1, or asking the manufacturer or distributor if it does not (How Acceptable is Warped Tile?, CTEF, 2025).

Warpage is why the offset matters. In a half-brick pattern, the crowned middle of one plank sits beside the ends of the next row, so the step at the joint grows.

Offset for plank tileWhat the standard and CTEF say
50% (half-brick)The pattern “amplifies actual tile warpage and likely results in unacceptable lippage” (CTEF)
More than 33%ANSI A108.02 4.3.8.2: “If an offset greater than 33% is specified, the specifier and owner must approve the mock-up and lippage” (CTEF, 2025)
33% or lessThe maximum where the side being offset is greater than 15 in. (nominal), “unless otherwise specified by the tile manufacturer” (CTEF, 2025)
Smaller, such as 25%A manufacturer may require “an even smaller offset” (CTEF); the carton or data sheet governs

Some older summaries put that size trigger at 18 inches (CTEF, 2022); a 24x48 plank is covered either way. The standard also sets running-bond grout joints for tile with any side over 15 inches at, on average, a minimum of 1/8 in. for rectified tile and 3/16 in. for calibrated tile, “increased over the minimum requirement by the amount of edge warpage” on the longest edge of the actual tiles (CTEF, 2025). CTEF also suggests widening the joint to make actual warpage less visible (CTEF).

How much mortar has to be under each large tile?

ANSI A108.5 section 3.3.2 (2017 edition), as quoted by CTEF in Never Assume You Have Sufficient Mortar Coverage, sets the average contact area at “not less than 80% except on exterior or shower installations,” where contact must reach 95%, checked by removing no fewer than three tiles, with “particular attention to this support under all corners of the tile.” Living areas fall under the first figure; a lanai, outdoor entry or shower floor falls under the second.

On large tile the corners and long edges lose support first, and an unsupported edge is where cracks and hollow spots start. The MegaLite data sheet spells out the method: a skim coat keyed in with the flat side of the trowel, ridges combed in one direction, the tile pressed back and forth across the ridges to collapse them, back-buttering where the tile needs it, and “Periodically pull up a tile and check the back.” Large-tile mortars are non-slump, so the ridges hold up under a heavy tile.

Heat shortens the working time. The same data sheet says mortar that has skinned over (“not sticky to the touch”) has to be recombed or replaced with fresh material. In a closed-up Florida house with the A/C off, or on a lanai in summer, that can happen while the row is still being set, so we mix smaller batches and check the bed before each tile.

Do tile leveling clips prevent lippage?

They help, within limits. A leveling system is a plastic base slipped under the edges of neighboring tiles, with a cap or wedge that pulls the edges into the same plane while the mortar cures. It keeps tiles from drifting as the next row goes in and evens out small differences at the joint.

It cannot remove a hump in the slab or the crown of a warped plank. Pompo’s lippage article warns that with too little thinset or too much lippage, the system “can pull the tile up too far and affect its bond” (CTaSC). The edge looks flush the day the clips snap off, but the tile sits on a thin or hollow spot. CTEF makes the same point from the other side: lippage control devices “work well only if they are used in accordance with the manufacturer's recommendations” (CTEF).

Clips are a finishing aid on a flat slab, never a substitute for flattening one. Our order on large tile: flatten the slab, dry-lay a few planks to check warpage and the offset, set with full coverage, clip, and pull a tile now and then to look at the back.

Where do movement joints and slab cracks go under large tile?

A large tile covers more slab, so it rides over more of the slab’s movement. The MegaLite data sheet says expansion joints and cold joints “should never be bridged with setting material. They must be brought through the tile work and filled with an appropriate elastomeric sealant,” and refers control and saw-cut joints to the manufacturer and to TCNA methods EJ171, F125 and F125A.

In practice that means planning the grid so a grout joint lands over each cold joint or moving saw cut, then filling that joint with color-matched sealant instead of grout. With 24x48 tile the layout has less room to shift, so we map the slab joints before the first tile goes down. A stable hairline crack usually gets a crack-isolation membrane under the tile, installed per its maker’s instructions; a crack with one side higher than the other needs to be looked at before any tile covers it.

Perimeter and field joints follow the same TCNA EJ171 spacing as any tile floor, with tighter spacing where sun hits the tile. Our article on why tiles pop up in Florida homes has that spacing table and the repair options when a floor has already tented.

What should a large-format tile quote include?

On our tile installation page, large-format porcelain (24x48 and up) is listed at $12–$19/sq ft, against $9–$14/sq ft for 12x24 and 24x24 porcelain; slab flattening, when needed, is priced after we check the slab. Whoever you hire, look for these lines before you sign:

We measure new floors free and send an itemized written quote within 24 hours. Installs carry our 1-year written labor warranty plus the manufacturer’s product warranty. Call Triangle Flooring at (941) 402-6861.

This is general information; the tile and mortar makers’ current instructions govern each installation.

Last verified: November 17, 2026.

Frequently Asked Questions

What size tile counts as large format?

Any tile with at least one edge 15 inches or longer. That is where ANSI A108.02 switches to its tighter substrate flatness rule, so 12x24, 24x24 and 24x48 tile all count. The longer the tile, the more both the slab and the tile's own warpage show.

How can I check porcelain planks for warpage before they are installed?

Open cartons from different boxes and lay two tiles face to face; a gap at the middle or at the ends shows crown or dish. A straightedge along the long edge tells you the same thing. Check that the carton or data sheet says the tile meets ANSI A137.1, and set the offset and joint width for the warpage you actually see.

Why does my new tile floor look uneven only in the late afternoon?

Low sun skimming across the floor casts a shadow at every grout joint, so small height differences that meet the standard can look like steps. The tile industry lists the angle of natural light as one of the factors that make lippage more visible. Judge the floor standing up in normal light; if an edge catches a toe or a sock, have it measured.

Can large-format tile go over a cracked slab?

Often, if the crack is stable and both sides are flush. Stable hairline cracks are usually covered with a crack-isolation membrane, while cold joints and moving cracks need a soft sealant joint in the tile right above them. A crack with one side higher than the other, or one that keeps growing, should be evaluated before tile goes down.

Will large-format tile raise the floor at doorways?

It can. Porcelain, a large-tile mortar bed and any leveler under it all add height, so doors, the dishwasher opening and transitions to carpet or vinyl need checking before work starts. We note those points at the free measurement and include trims or door undercuts in the written quote.

Is a cracked large tile hard to replace?

Harder than a small one, because a 24x48 tile has to be cut out without chipping its neighbors and the new piece must match the original lot. Keep at least one full carton of spares from the same lot, stored flat. Our published price for cracked tile replacement is $95–$175 per tile, including matching grout.

JM
Jose Mauricio — Triangle Flooring

Owner and lead installer at Triangle Flooring, an insured flooring contractor based in Palmetto, FL, serving Manatee, Sarasota, Hillsborough and Pinellas counties since 2023. Every install is backed by a 1-year written labor warranty.